|
Silent and Vehicle Power Supply Kits
DC-DC Converters
Universal AC Adapters
Silent PSU Kits
Intelligent Vehicle PSUs
Internal Power Cables and Adapters
PSU Selection Table (opens a new window)
DC-DC Converters
DC-DC converters accept a single direct current input, and convert it into very stable 3V, 5V and 12V lines that a Mini-ITX motherboard needs. The DC input will normally come from an external AC Adapter.
picoPSU-150-XT 12V DC-DC ATX PSU (Socket board compatible)  | | picoPSU-150-XT DC-DC ATX Power Supply (150 Watts) |
| | | | | | | IN STOCK (Checked 05:56 GMT) |
|
|
| |
Plugs directly into the motherboard ATX connector. Generates up to 150 Watts of power from a 12V supply, at over 96% efficiency. An attached cable harness provides one 24 pin ATX connector, one PATA HDD, one SATA HDD and one 12V P4 power connector.
The picoPSU-150-XT can power all our Mini-ITX boards with a 24 pin ATX connector, and is ideally suited for use with socket CPU Mini-ITX boards such as the Intel DG45FC, Zotac 9300, 630i and 610i boards. The Jetway J7F2, J7F4K, J7F5M boards also have 24 pin ATX connectors. The Jetway JNC91 and JNC92 have 20pin ATX connectors but the picoPSU-150-XT will fit. Other Mini-ITX boards with 20 pin ATX connectors may not work, due to positioning of components on the boards.
You will need a 12V AC Adapter to use the picoPSU. Three compatible Universal 12V AC adapters are available - 60W, 80W and 110W. Select the 110W AC Adapter if you are using a socket CPU Mini-ITX board (we recommend 65W TDP CPUs maximum). 60W and 80W AC Adapters are enough for embedded Mini-ITX boards (e.g. Atom, C7 powered)
|
picoPSU-120 12V DC-DC ATX PSU  | | picoPSU-120 12V DC-DC ATX Power Supply (120 Watts) |
| | | | | | | IN STOCK (Checked 05:56 GMT) |
|
|
| 12V P4 Power Cable and Molex Y Splitter (*see note) |
| | | | | | | IN STOCK (Checked 05:56 GMT) |
|
|
| |
The world's smallest snap-in 12V DC-DC ATX power supply unit, measuring just 31x45x20mm, about the size of two AA batteries. Patent Pending HyperWatt™ technologies, fully ATX compliant, 100% silent.
Plugs directly into the motherboard ATX connector. Generates up to 120 Watts of power from a 12V supply, at over 96% efficiency. An attached cable harness provides one HDD, one SATA and one floppy/slimline optical drive power connector. Cable lengths: from board to 12V DC connector is approx 25cm (9.75"); cable harness is approx 40cm (15.75") long.
More pictures of the picoPSU
The picoPSU-120 can power all our Mini-ITX boards with Geode, C3 and C7 processors, and (with a 110W AC Adapter) Intel Mobile Socket Mini-ITX boards. Additionally *some* other lower power consumption Mini-ITX and regular boards with P3, P4, Pentium-M, and AMD processors can be powered. If you are enquiring about a board not on our site, please email us to check compatibility. Notes: picoPSU-120 prior to Dec 1 2007 had 2 x HDD and one floppy connector; the picoPSU will NOT plug directly into the power connector on an EPIA MS board (due to the size of the heatsink); Can be used with an Atom board (with a Molex to 12V P4 power connector)
*Note: If your board has a 4 pin 12V P4 power connector, you will need our 12V P4 Power Cable and Molex Y Splitter cable bundle. Current boards that require 12V P4 power include: Intel Atom boards, DG45FC, Zotac 610, 630 and 9300 boards, Jetway JNC62K, JNC81. Choose 110W AC Adapter for socket boards, 60W or 80W AC Adapter for embedded boards.
You will need a 12V AC Adapter to use the picoPSU. Three compatible Universal 12V AC adapters are available - 60W, 80W and 110W. Please read their notes to determine which is most suitable for you.
CE / FCC / VCCI Certifications (applies to all picoPSUs): EN55024, EN55022 Class B (CE certification), Australia/New Zealand (using CISPR 22, EN55022), Japan (VCCI: using CISPR 22, ANSI C63.4), United States (FCC Part 15, Subpart B, Class B), Canada (ICES-003 using CISPR 22, ANSI C63.4).
Product Manual (PDF)
|
picoPSU-90 12V DC-DC ATX PSU (Atom compatible)  | | picoPSU-90 12V DC-DC ATX Power Supply (90 Watts) |
| | | | | | | IN STOCK (Checked 05:56 GMT) |
|
|
| |
Plugs directly into the motherboard ATX connector. Generates up to 90 Watts of power from a 12V supply, at over 96% efficiency. An attached cable harness provides one 20pin ATX, one PATA HDD, one SATA and one 12V P4 power connector.
The picoPSU-90 can power all our Mini-ITX boards with Geode, C3 and C7 processors, and is ideally suited for use with the Intel D945GCLF and D945GCLF2 Atom boards, as it has a 12V P4 power connector. Please use the picoPSU-120 or picoPSU-150-XT if you require more power. If you are enquiring about a board not on our site, please email us to check compatibility. Note: The picoPSU will NOT plug directly into the power connector on an EPIA MS board (due to the size of the heatsink).
You will need a 12V AC Adapter to use the picoPSU. Three compatible Universal 12V AC adapters are available - 60W, 80W and 110W. Please read their notes to determine which is most suitable for you.
|
picoPSU-60 WI 6-26V DC-DC ATX PSU  | | picoPSU-60 WI 6-26V DC-DC ATX Power Supply |
| | | | | | | IN STOCK (Checked 05:56 GMT) |
|
|
| |
* New 6-26V, 60W version *
Plugs directly into the motherboard ATX connector. This new 60W version generates up to 60 Watts of power (80 Watts peak) from a 6 to 26V power supply, at over 94% efficiency.
The picoPSU-60 WI can power all boards with C3 or C7 processors. Not suitable for Intel Atom based boards due to low power output on 12V line (choose picoPSU-80 WI instead). If you are enquiring about a board not on our site, please email us to check compatibility.
You may need a 12V AC Adapter to use the picoPSU. Three compatible Universal 12V AC adapters are available - 60W, 80W and 110W. Please read their notes to determine which is most suitable for you.
|
picoPSU-80 WI 12-25V DC-DC ATX PSU  | | picoPSU-80 WI 12-25V DC-DC ATX Power Supply |
| | | | | | | IN STOCK (Checked 05:56 GMT) |
|
|
| |
Plugs directly into the motherboard ATX connector. This new 80W version generates up to 120 Watts peak from a 12 to 25V power supply, at over 94% efficiency.
The picoPSU-80 WI 12-25V can power all C3, C7 or Atom based boards. Harness does not have 12V P4 power connector - use a Molex adapter if your board requires this. If you are enquiring about a board not on our site, please email us to check compatibility.
You may need a 12V AC Adapter to use the picoPSU. Three compatible Universal 12V AC adapters are available - 60W, 80W and 110W. Please read their notes to determine which is most suitable for you.
|
picoPSU-80 WI 12-32V DC-DC ATX PSU | | picoPSU-80 WI 12-32V DC-DC ATX Power Supply |
| | | | | | | IN STOCK (Checked 05:56 GMT) |
|
|
| |
* New 12-32V, 120W peak version *
Plugs directly into the motherboard ATX connector. This new 80W version generates up to 120 Watts peak from a 12 to 32V power supply, at over 94% efficiency.
The picoPSU-80 WI 12-32V can power all C3, C7 or Atom based boards. Harness does not have 12V P4 power connector - use a Molex adapter if your board requires this. If you are enquiring about a board not on our site, please email us to check compatibility.
You may need a 12V AC Adapter to use the picoPSU. Three compatible Universal 12V AC adapters are available - 60W, 80W and 110W. Please read their notes to determine which is most suitable for you.
|
Universal AC Adapters
AC Adapters convert alternating mains voltage (from 100 to 240V) to a regulated 12V output. Our AC Adapters (are suitable in combination with a DC-DC converter) as full PSU kits, or can be used as replacements or spares (e.g. some Hush or Tranquil Mini-ITX PCs, Morex Cubid and some Travla cases).
60W AC Universal Adapter 12V 5A
80W AC Universal Adapter 12V 6.6A
110W AC Universal Adapter 12V 9A
Intelligent Vehicle PSU Kits
Our intelligent Vehicle PSU kits will provide a regulated output to your Mini-ITX board, while monitoring the battery of your vehicle. Rapid voltage changes are protected against, and graceful timed shutdowns are possible. These require more auto-electrical knowledge than our Easy-Install kits, but if you have the time and the inclination, are well worth it.
M1-ATX 90W Intelligent Vehicle DC-DC Power Supply  | | M1-ATX Vehicle DC-DC Power Supply, 6-24V 90W |
| | | | | | | IN STOCK (Checked 05:56 GMT) |
|
|
| |
Designed to provide power and to control the ON/OFF switch of a motherboard (PC) based on ignition status, M1-ATX is a wide input (6-24V) vehicle or car DC-DC ATX power supply capable of surviving tough car engine cranks (down to 5.7V) as well as transient over-voltage situations.
8 user selectable microcontroller driven timing modes, allowing you to choose up to 8 ignition/shutdown vehicle / car timing schemes. While in deep sleep mode, M1-ATX constantly monitors your car battery voltage levels, automatically shutting down until battery levels reach safe levels.
M1-ATX comes equipped with ATX, Molex HDD, SATA HDD and Floppy cable harness, jumpers, faston connectors and 2 pin cables for motherboard ON/OFF switch. Just connect it to your 12V or 24V car/boat/RV battery and power up your PC.
Designed to work with the VoomPC and VoomPC 2, but is also a direct size compatible replacement with Morex 26xx, 27xx, 36xx, Travla C134, C150, C158, C159 and Tranquil T2e cases. Dimensions: 45mm x 160mm (1.77in x 6.31in). 90W Output. Not compatible with EPIA PD boards. For Pentium M boards, please use the M2-ATX.
Product Manual (PDF) |
M2-ATX 160W Intelligent Vehicle DC-DC Power Supply  | | M2-ATX Vehicle DC-DC Power Supply, 6-24V 160W |
| | | | | | | IN STOCK (Checked 05:56 GMT) |
|
|
| |
Designed to provide power and to control the ON/OFF switch of a motherboard (PC) based on ignition status, M2-ATX is a wide input (6-24V) vehicle or car DC-DC ATX power supply capable of surviving tough car engine cranks (down to 5.7V) as well as transient over-voltage situations.
8 user selectable microcontroller driven timing modes, allowing you to choose up to 8 ignition/shutdown vehicle / car timing schemes. While in deep sleep mode, M2-ATX constantly monitors your car battery voltage levels, automatically shutting down until battery levels reach safe levels.
M2-ATX comes equipped with ATX, Molex HDD, SATA HDD and Floppy cable harness, jumpers, faston connectors and 2 pin cables for motherboard ON/OFF switch. Just connect it to your 12V or 24V car/boat/RV battery and power up your PC.
Designed to work with the VoomPC and VoomPC 2, but is also a direct size compatible replacement with Morex 26xx, 27xx, 36xx, Travla C134, C150, C158, C159 and Tranquil T2e cases. Dimensions: 45mm x 160mm (1.77in x 6.31in). 160W Output - ideal for our Pentium M/Intel Core boards. Not compatible with EPIA PD boards.
Product Manual (PDF) |
M2-ATX-HV 140W Intelligent Wide Input Vehicle DC-DC Power Supply  | | M2-ATX-HV Vehicle DC-DC Power Supply, 6-32V 140W |
| | | | | | | IN STOCK (Checked 05:56 GMT) |
|
|
| |
* NEW *
Designed to provide power and to control the ON/OFF switch of a motherboard (PC) based on ignition status, M2-ATX-HV is a wide input (6-32V) vehicle or car DC-DC ATX power supply capable of surviving tough car engine cranks (down to 5.7V) as well as transient over-voltage situations.
8 user selectable microcontroller driven timing modes, allowing you to choose up to 8 ignition/shutdown vehicle / car timing schemes. While in deep sleep mode, M2-ATX-HV constantly monitors your car battery voltage levels, automatically shutting down until battery levels reach safe levels.
M2-ATX-HV comes equipped with ATX, Molex HDD, SATA HDD and Floppy cable harness, jumpers, faston connectors and 2 pin cables for motherboard ON/OFF switch. Just connect it to your 12V or 24V car/boat/RV battery and power up your PC.
Designed to work with the VoomPC and VoomPC 2, but is also a direct size compatible replacement with Morex 26xx, 27xx, 36xx, Travla C134, C150, C158, C159 and Tranquil T2e cases. Dimensions: 45mm x 160mm (1.77in x 6.31in). 140W Output - ideal for our Pentium M/Intel Core boards. Not compatible with EPIA PD boards.
Product Manual (PDF) |
M3-ATX PicoPSU Form-Factor Intelligent Vehicle DC-DC Power Supply  | | M3-ATX Intelligent Vehicle DC-DC Power Supply |
| | | | | | | IN STOCK (Checked 05:56 GMT) |
|
|
| |
* NEW *
Designed to provide power and to control the ON/OFF switch of a motherboard (PC) based on ignition status, M3-ATX is a wide input (6-24V) vehicle or car DC-DC ATX power supply capable of surviving tough car engine cranks (down to 6V) as well as transient over-voltage situations.
The M3-ATX is based on a similar electrical similar design to the M2-ATX but with dramatic size reductions (picoPSU plug-in style).
M3-ATX comes equipped with a ATX, Molex HDD, SATA HDD and Floppy cable harness, jumpers, faston connectors and cables for Thump and Motherboard ON/OFF switch. Just connect to your 12V or 24V car/boat/RV battery and power up your PC.
Programmable shutdown / sleep modes via optional serial cable; Fits any motherboard equipped with a 20 or 24pin ATX connector; 100% silent, fanless, no moving parts; Operates from 6-24V, multi-chemistry batteries supported; Highly efficient design, does not produce a lot of heat; Ideal for low power Intel Core Duo as well as all VIA or AMD processors.
Product Manual (PDF) |
Internal Power Cables and Adapters
Nano-PSU Plug in Adapter for Nano-ITX Boards  | | Nano-PSU Plug in Adapter for Nano-ITX Boards |
| | | | | | | IN STOCK (Checked 05:56 GMT) |
|
|
| |
This adapter replaces the bulky cable provided with Nano-ITX boards, converting 20 pin ATX pins to the smaller 10 pin Nano-ITX format.
Plugs directly into the Nano-ITX motherboard, ideal for use with Pico-PSU power supplies.
|
Molex Power Splitter Cable - 2x HDD Connectors  | | Molex Power Splitter Cable - 2x HDD Connectors |
| | | | | | | IN STOCK (Checked 05:56 GMT) |
|
|
| |
Splitter cable converts one HDD connector into two, allowing you to mount that extra hard drive.
|
Molex Power Splitter Cable - 1xHDD and 1xFloppy Connector  | | Molex Power Splitter Cable - 1xHDD and 1xFloppy Connector |
| | | | | | | IN STOCK (Checked 05:56 GMT) |
|
|
| |
Splitter cable converts one HDD connector into a HDD connector and a floppy connector, allowing you to mount that extra compact flash adapter or slimline optical drive.
|
Serial ATA Power Cable  | | | | | | | | IN STOCK (Checked 05:56 GMT) |
|
|
| |
Most PSUs (including all the PSUs on Mini-ITX Cases we sell) come with standard 4-pin Molex connectors for connection to IDE ATA Hard Drives.
To power a Serial ATA drive from one of our cases, you will require this adapter cable.
|
Don't see what you want here? Send us an email with as much information as possible, and we'll try and get it for you.
|
Cards accepted directly:
 |
 |
 |
 |
| Additionally with PayPal: |
 |
 |
 |
|
